How To Change Lock Cylinder On Commercial Door

Download Article

Lock cylinders are the internal mechanism within a lock. Interchangeable lock cylinders are ofttimes found in residential and office doors, while storefront lock cylinders are typically found in the doors for retail outlets and businesses. Lock cylinders can also exist found in the ignition in most vehicles. If you want to alter the primal in your lock, information technology'southward probable you'll have to replace the lock cylinder. Luckily, doing so tin be easy as long as you have the right tools and follow the right steps.

i
Remove the flat screw under the latch. Prop open the door as you alter the lock. Plow the screw under the door latch counterclockwise with a flathead screwdriver and remove it.^[1]
- Put the screw somewhere safe because you'll have to screw it back in later.
two
Turn the primal a quarter of the way. Insert the key into the keyhole and plow it slightly so that information technology'southward in the open position. This will hide the latch in the internal components of the lock and allow yous to slide information technology out.^[2]
- If you don't plough the primal so you won't be able to pull out the lock.
Advertisement
iii
Pull on the key while pushing on the other side of the lock. Go on the cardinal turned while you push on the lock from the other side of the door. If done correctly, the interchangeable lock cylinder should come out.^[3]
- If the cylinder feels stuck, endeavor turning the fundamental a little more than or less. Adjust the cardinal until you can push the latch out.
four

Turn the key and slide the new cylinder into the pigsty. Turn the key counterclockwise a quarter of the way open so that the latch goes inside of the lock cylinder. This will allow you to easily slide information technology back into the cylinder pigsty.^[4]
5
Screw the apartment spiral back in. Thread the screw into the hole with your fingers, so utilize a flathead screwdriver to tighten information technology. Keep turning it until information technology runs flush with the side of your door.^[5]
- Screwing in the apartment screw will hold the lock cylinder in place.
6

Examination your fundamental to brand certain that it unlocks your door. Keep the door open as you test it. If information technology doesn't work, attempt dissembling and reinstalling the lock cylinder or call a locksmith to see if they tin can supercede it for you lot.^[6]

Advert

1
Unscrew and remove the faceplate over the latch. Use a doorstop to prop the door open while y'all're working. Detect the faceplate on the thin role of the door and use a Phillips head screwdriver to remove all the screws in it. Once the screws are out, pop the faceplate off the door.^[7]
- Place the screws in a sealable purse so that you lot don't lose them.
2
Loosen the gear up screw nearly the lock itself. The set screw will exist the spiral closest to the lock cylinder on the outside of the door. Use a Phillips head screwdriver to plow the fix screw counterclockwise until you loosen information technology.^[8]
- Loosening the set screw will allow you to rotate the lock cylinder. You don't have to remove the set spiral entirely, only loosen information technology enough so that you can turn the lock cylinder.
3
Insert a key into the lock and turn it clockwise to unscrew it. Utilize a dissimilar key than the one that unlocks the door so that y'all can utilise it every bit a wrench. Insert the mismatching primal into the keyhole and plough information technology counterclockwise to loosen the cylinder. When the cylinder is loose enough, information technology should easily come up out of the hole in the door.^[9]
- If y'all discover a lot of resistance, loosen the fix screw more.
4
Thread a new lock cylinder into the hole. Put the new lock cylinder into the pigsty with the keyhole facing outward. Start threading the new cylinder by turning it clockwise in the hole.^[10]
- If in that location is a lot of resistance as y'all're turning the key, it's an indication that the threads aren't catching correctly. In this example, unscrew the cylinder and start over from the beginning.
5
Insert a mismatching key into the lock and turn information technology clockwise. Again, use a central that isn't fabricated for the lock then that it catches and can exist used as a wrench. End turning the cylinder when you lot feel resistance and the keyhole is on the bottom of the lock.^[xi]
- Every bit you turn the fundamental, make sure that the threads on the cylinder are fitting in the threads around the hole for the lock.
6

Re-tighten the fix screw. Plough the set screw clockwise to set the new lock cylinder in identify. Once the set spiral is tight, you should no longer exist able to rotate the lock cylinder.^[12]
seven

Screw the faceplate back on and examination the lock. Fit the faceplate over the latch and line up the holes in the latch with the holes in the door. Utilize a screwdriver to secure the screws back in their holes. Employ the correct key on the new lock to make sure that you installed it correctly and the door locks.^[xiii]

Advertising

1
Find the admission hole to your ignition. About models of cars volition accept an ignition access hole somewhere around the steering wheel. Check your user'due south manual to find information technology on your car. On Fords, there are commonly three holes under your steering wheel. The smallest hole should be in the middle and is the access hole for your ignition.^[14]
- On Chevrolet make cars, the admission pigsty can unremarkably exist institute on the tiptop of the steering wheel.^[15]
- New cars that accept electronic or button ignitions don't have lock cylinders.
- If y'all don't take an ignition access hole, yous'll demand to remove the bottom of your steering cycle.
2
Put your fundamental in the ignition. Your central needs to be in the ignition or you won't be able to release the lock cylinder. Keep the central in the ignition equally you go along working. Practise not turn on the car.^[16]
- Yous don't have to plow the key initially.
3
Push an Allen central into the hole. Every bit you push the Allen cardinal into the hole, it should disengage the locking mechanism on the lock cylinder. You'll take to go on the Allen key pressed into the hole as you move onto the next pace.^[17]
- The Allen key disengages the locking mechanism in the lock cylinder.
4
Plow the ignition clockwise until it clicks. You should hear 2 clicks once the ignition disengages. Your machine should non get-go. Y'all tin can now release the Allen key from the pigsty.^[18]
- Go on the fundamental in the ignition.
5

Pull the key ignition out. The ignition, or lock cylinder, should pop out subsequently you plough it. Pull on the primal to pull the lock cylinder completely out of its casing. If the ignition is sticking, wiggle it dorsum and forth until you free it from its pigsty.^[nineteen]
6
Insert the new lock cylinder and turn it counterclockwise until information technology clicks. Push button your new lock cylinder into the pigsty and twist it towards you. The spring should appoint, locking the new cylinder into place. Your new lock cylinder is now installed.
- Y'all should hear it click when your ignition locks in place.
Advertizing

Add New Question

Question

Is information technology cheaper to rekey or replace locks?

This answer was written by one of our trained squad of researchers who validated it for accuracy and comprehensiveness.

wikiHow Staff Editor

Staff Answer

Support wikiHow by unlocking this staff-researched answer.

Key pins are quite inexpensive, then it'south normally cheaper to rekey your locks than to change them. About locksmiths volition only accuse labor instead of charging you for both labor and parts, as they'd need to if you lot had your locks inverse.
Question

How do you lot change the cylinder on a UPVC door lock?

This answer was written by one of our trained squad of researchers who validated it for accuracy and comprehensiveness.

wikiHow Staff Editor

Staff Answer

Back up wikiHow by unlocking this staff-researched answer.

Unscrew the screw on the faceplate along the edge of the door. Put the key on the inside lock barrel and plough it slightly to the left and correct wile pulling it toward you lot at the aforementioned fourth dimension. Eventually, the cylinder volition slide out. Simply contrary the process to install a new cylinder.
Question

What do you do if the lock cylinder pops out past accident?

This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.

wikiHow Staff Editor

Staff Respond

Support wikiHow by unlocking this staff-researched answer.

Information technology this happens, it probably means that the lock has been damaged. For some kinds of locks, you tin can buy a small retainer clip to help go on the cylinder in identify. If the lock is besides badly damaged, you may accept to replace the whole matter.
Question

What do I do if I don't have the original central?

Yous will need to extract the core from the lock and have a locksmith who knows how to work with Interchangeable Cores "decode" your core (accept all the pins out of the cadre) and provide you with the key codes. You will then need to utilise the key code for the original key for the locksmith to create a copy of the primal based on the original key code.

Ask a Question

200 characters left

Include your e-mail accost to get a message when this question is answered.

Submit

Advertising

Thanks for submitting a tip for review!

Things Yous'll Need

Flathead screwdriver
Primal

Screwdriver
Key

Allen key
Key

Near This Commodity

Article Summary X

Replacing a lock cylinder tin can be washed by following a few elementary steps. Start, you'll need to remove the screw below the latch. Then, turn your key a quarter of the fashion so information technology'south in the open position, which will allow you to pull out the cylinder. Y'all'll need to pull on the key while pushing the lock from the other side of the door, which should cause the cylinder to pop out. If it doesn't, try turning the key slightly more than or less until the cylinder comes loose. When you're prepare to install the new cylinder, turn the key a quarter of the way counter-clockwise and so you can insert information technology. Then, insert the flat screw below the latch. For tips on how to replace a storefront lock cylinder, keep reading!

Did this summary help you?

Thanks to all authors for creating a folio that has been read 308,145 times.